[SunRescue] parts I'm parting with!

[MikeHebeldruaga at pmail.net]

It totally depends on the model of the monitor.  I believe (I may be wrong
here) that the 17" ones work on some systems.  Most of the time the
Sync-on-green issue is what stops the cross-usage from SGI to Sun and back.

Check out the links below.

I may be incorrect.

Sincerely,

Mike Hebel

-----Original Message-----
From: rescue-admin at sunhelp.org [mailto:rescue-admin at sunhelp.org]On
Behalf Of Alan Rubin
Sent: Friday, September 15, 2000 9:30 AM
To: rescue at sunhelp.org
Subject: RE: [SunRescue] parts I'm parting with!


i didn't really read this whole thread, but am i to understand that a
stock SGI monitor with a 13w3 type connector on the back will not work
with, say, an IPX?  i need to know before i might pick up a spare from
work for home.

alan

On Fri, 15 Sep 2000, Mike Hebel wrote:

> <SNIP>
> >. 21" Sun monitor
>
> >>With a little soldering, I have successfully modified my 20D11 to work
> with
> >>Suns, and if you're willing to do the same, you can turn that SGI
monitor
> >>into the Sun monitor you're looking for.
> >>
> >>Since the 20D11 expects sync-on-green, what you have to do is connect
the
> >>separate sync pin used by Sun (and others) to the sync separator
circuit.
> >>This is as simple as soldering in one resistor on the input board at the
> >>back of the monitor. The connector on the monitor conveniently has all
> pins
> >>soldered to the PCB even though most of them aren't used. I can open
mine
> >>up again if you want and give you specific instructions on what I did.
And
> >>yes, it works with both Suns and SGIs after the mod, though you have to
> use
> >>Sun or SGI cables as appropriate. And no, it still won't work with a PC,
I
> >>suspect because of the limited sync range, or maybe my HD15-to-13W3
> adapter
> >>is bad.
> >>
> >>I don't remember the sync range of the 20D11, but I have tested my
> modified
> >>one with a stock Indy and a stock SS2+cg6, and it works great.
>
> I don't suppose you could post a picture of the modification somewhere as
> well as the value of the resistor?  I would be more than thankful for the
> detailed instructions you offered.  (I have two 20D11 monitors attached to
> SGI boxes that I would like to also use with my SS2 and possibly other
> SPARCs.)
>
> Also, unless it's the frequency converting kind the HD15-to-13W3 adapter
> won't work in most modes on a PC.  I _know_ this monitor will not run at
DOS
> resolutions.  Check out the links from http://sgihelp.org - they have a
link
> here: http://www-viz.tamu.edu/~sgi-faq/faq/html-1/hardware.html#20 which
is
> a hardware FAQ about SGI monitors.  Plenty of notes here and elsewhere
about
> getting it to run on a PC.
>
> Hope this helps!
>
> Sincerely,
>
> Mike Hebel
>
> _______________________________________________
> Rescue maillist  -  Rescue at sunhelp.org
> http://www.sunhelp.org/mailman/listinfo/rescue
>
>

_________________
*Alan Rubin*
Sun/Unix/Networking/ISP/Web Writing
Email:rubin at ezy.net


_______________________________________________
Rescue maillist  -  Rescue at sunhelp.org
http://www.sunhelp.org/mailman/listinfo/rescue