[rescue] Sun Netra T1125

[Peter Stokes]

Hi

I think that the 480Mhz are 450 only, the 420 only supported the 450Mhz as per
the T1125/Ultra 60. The 450 supported the 250, 300, 400 and 480Mhz from
memory.

Never tried the 480Mhz in an Ultra 60, normally mixing the CPUs does not work,
but obviously does in this case, but suspect that you will only get 450Mhz out
of it.

Peter

> On 11 Nov 2019, at 11:56, Richard <ejb at trick-1.net> wrote:
>
> o;?Hi everyone
>
> OK so the T1125 is now up and running. It had its issues but would boot both
CPU to Solaris 10 (no root passwd so reinstalled) when it arrived. however
> - 1 of the 2 drives was dead, removed the dead one...ordered a replacement
> - NVRAM Battery was dead and the system complained about ID PROM INVALID
etc..
> - After replacing the NVRAM Battery the machine wouldn't boot and gave a RED
State Exceptions on power up. Removing the second CPU (CPU1) seemed to resolve
the issue, using CPU1 as CPU0 also resulted in RED State Exception so I am
guessing the CPU is the issue.
>
> One interesting point is that both CPU are 480Mhz CPU Module with 8M Cache
(501-5729)...have not found anything to indicate that thats a supported
configuration. All I can find is that it is supported for Enterprise 450,
420R...I note that OBP reports as 450Mhz CPU. Anyone have any insight? Anyone
got a spare they would be willing to part with? Is it an OS level issue
similar to that in the following
http://shrubbery.net/~heas/sun-feh-2_1/collections/intsrdb/24408.html
>
> Ordered the following to max the machine out...
> - Extra Gig of memory
> - Replacement drive
> - Gig ethernet card
>
> So current state
> - Solaris 8 + Recommended Patch bundle + SUNWspci2 + SUNWspvnc
> - TECH-SOURCE gfxp
> - 3x SunPCI II Cards (will probably drop back to 2 when the Gig ethernet
card turns up.
>
> # ./sunpci -l
> Opening a SunPCi window...
>
>  Name = Card1
>    Device = /dev/sunpci2drv0
>    Type = SunPCi II
>    Description = SunPCi II card
>    Peripherals =
>    ID = 00:03:BA:13:58:D6
>
>  Name = Card2
>    Device = /dev/sunpci2drv3
>    Type = SunPCi II
>    Description = SunPCi II card
>    Peripherals =
>    ID = 00:03:BA:10:F2:D0
>
>  Name = Card3
>    Device = /dev/sunpci2drv6
>    Type = SunPCi II
>    Description = SunPCi II card
>    Peripherals =
>    ID = 00:03:BA:10:F3:4A
>
> thanks in advance
>
> Richard
>
>
>> On Tue, 29 Oct 2019, at 11:32 PM, Dennis Grevenstein wrote:
>> Hi,
>>
>> Richard wrote:
>>>
>>> Answering my own question...:-)
>>>
>>> Yes will work with 9 and possibly 10 with some work arounds.
>>>
>>> Documentation indicates can install multiple cards in the same
machine...I
>>> have 3 so letbs see how that goes :-) will have to watch that 25W per
card
>>> power requirement.....
>>
>> I think this depends on the exact version of the SunPCi card.
>> The later versions II and III should work. The earliest SunPCI
>> may not.
>>
>> Dennis
>> _______________________________________________
>> rescue list - http://www.sunhelp.org/mailman/listinfo/rescue
> _______________________________________________
> rescue list - http://www.sunhelp.org/mailman/listinfo/rescue